SANLI BSB 33 Spécifications

PLEASE KEEP THIS MANUAL IN A SAFE PLACEBSB 60Back-Pack Leaf Blower

8Before fueling, clean the filler cap and the area a around it to ensure that no dirt falls into the tank.Drain the fuel tank.Use a hook to pull the f

9Observe safety precautions - see chapter" Safety Precautions".Slide the stop switch (1) to ONIf the engine is cold, turn the choke knob toI

10When engine begins to fire:If engine is cold:Turn choke knob to and continue cranking until engine runs.If engine is warm:Continue cranking unt

11Fuel tank run until dry and then refueledFit the spark plug and reconnect the spark plug boot.Move the stop switch to ONTurn the choke knob to

If there is a noticeable loss of engine powerDirty air filers reduce engine power increase fuel consumption and make starting more difficult.Remove th

Fine Tuning for Operation at High AltitudeChecking the Spark Plugcheck the standard setting.Warm up the engine.Turn the high speed screw (H) slightly

If the spark plug comes with a detachable adapter nut (1), screw it on fi rm ly.Always press the boot (2) firmly on to the spark plug (3).On all spar

Remove the spring clip (3).Remove the rope rotor with washer (4) and pawl (5).Ease the cap (6) out of the starter grip.Remove remaining rope from the

Make a loop in the unwound starter rope and use it to turn the rope rotor six full revolutions in the direction of the arrow (see illustration).Hold t

17Minimize Wear and Avoid DamageObserving the instructions in this manual helps reduce the risk of unnecessary wear and damage to the power tool.The p

Contents1. Guide to using this manual………………………………………...1 2. Safety precautions………………………………………………… .2 3. Maintenance and repair…………………………………………...6

SpecificationsSingle cylinder two-stroke engineDisplacement: 56.5 cm3Bore: 46 mmStroke: 34 mmId

IE46F-3 GASOLINE ENGINE EXPLOSIVE PICTURE

Ser.No.Erp No.Part NameQtySer.No. Erp No. Part NameQty1-1166881-16290311-21-3SCREW1-261-41-51-628111-71-81-91-101-2560834253281328811-111-121-131-141-

BSB60 EXPLOSIVE PICTURE OF FRAME AND SPRAYING

BSB 60 SPARE PARTS LIST OF IMPLEMENT PICTURE1111111111111018015645164620540867469811886441386458643864486757808645083136231284112224290011736536698369

EC DECLARATION OF CONFORMITYFujian Jinjiang Sanli Engine Co., Ltd.Declares that the following equipment manufactured by Fujian Jinjiang Sanli Engine C

Notes

AddressBSB 60

Sanli UK LtdUnit 200 Milton Park EstateAbingdon Oxfordshire OX14 4TBwww.sanli.co.ukSANLI FRANCE SASService garantie 10,RueGutenberg 67610 LAWANTZENAUw

1Guide to Using this ManualPictogramsEquipment and featuresEngineering improvementsSymbols in textAll the pictograms attached to the machine are show

2You must be fit to work with a blowerWear proper clothing and equipmentWear safety glasses,goggles or a face shield.Only attachments supplied are exp

3Unit vibrations can cause an improperly tightened fuel cap to loosen or come off and spill quantities of fuel.Check the following points:Throttle tri

4Always hold your unit firmly- make sure you always have a firm and secure footing.On ice, in wet or snowOn slopes or uneven groundRoots, ditches, hol

5- Any personal tendency to suffer from poor circultaion (symptoms: frequently cold fingers, itching).- Low outside temperatures.- Grippin

6Turn the control handle counterclockwise to the horizontal position.Now rotate the extension rube counterclockwise until the metering unit points in

7Lift the tabs of the two sliding adjusters.Adjust the straps so that the backplate is held firmly and comfortably against your back.Loosening the har